Draft preview — not published. Phone and email are placeholders.

FAQ

Questions we are often asked

Short answers on servicing, adoption, local conditions and emergency attendance. If your question is not here, please use the contact form or telephone once a number is in service.

How often should a pumping station be serviced?

It depends on how hard the station works. As a guide, low-use domestic stations are often well served by an annual visit; commercial, development and high-use sites usually need servicing quarterly, or a contract with two or four visits a year. Stations on the Thames, Wey or Mole floodplains, or those serving kitchens with a heavy load of fats, may need more frequent desilting as well as the mechanical service. We will say if a proposed schedule looks too light for the site.

Do you only work on stations you have installed?

No. We maintain and repair stations of any make, design, age or condition, including packaged GRP chambers and older brick or concrete wet wells. If you have inherited a station and have little paperwork, a first inspection and a tanker clean is often the most useful place to start.

What is Section 104, and who is responsible for an unadopted station?

Section 104 of the Water Industry Act 1991 is the usual route by which a developer agrees that sewers and, where relevant, a pumping station will be adopted by the sewerage undertaker — in most of Surrey, Thames Water. Until adoption is completed, and in every case where a station remains private, responsibility sits with the developer or with the management company or residents who have taken the site on. Adoption can take a long time. A service contract does not replace the adoption agreement, but it does keep the station working in the meantime.

Why do stations in parts of Surrey seem to silt up or fail so often?

Three local reasons come up again and again. Fine clay and grit from London Clay soils settle in the sump and wear pumps. Fats, oils, grease, rags and wipes form a mat on the surface and catch on impellers and floats. On the Thames, Wey and Mole corridors, high groundwater and storm flows ask a lot of surface-water and combined stations, so a pump that has not been tested, or a chamber that has not been desilted, shows up quickly.

What should I do if the high-level alarm sounds?

Treat it as urgent. A high-level alarm means the pumps have not kept up, or have not been told to start. If you have an emergency number for the station, use it. On this draft site the telephone number is a placeholder and is not yet in service; once a local number is confirmed it will appear in the header and on the contact page. Do not wait to see if the level drops on its own, particularly on a basement, a car park or a housing development. If it is safe to do so, note whether any pump-running lights are on, and whether the alarm has a mute, so you can tell the engineer what you have seen.

What is included in a major service?

The major service is a 21-point check: the pumps are lifted and cleaned, and we inspect the volute, impeller, wear rings, bearings, oil (for water ingress), motor windings and cables, floats or ultrasonic head, lifting gear, isolation and non-return valves, pipework, chamber and covers, and the control panel, including alarms and earth loop resistance. The chamber is cleaned of items that could cause a blockage. A general service is a shorter version of the same inspection. The full list is on the services page.

Can you desilt the chamber and jet the pipework?

Yes. Tanker pump-outs and high-pressure jetting are available as an emergency attendance or as part of a maintenance contract, typically once a year, more often on a busy site. This removes fats, oils and grease, rags, wipes and sediment that a standard mechanical service cannot fully deal with.

Do you cover basement sump pumps and underground car park drainage?

Yes. Basement foul pumps, grey-water lifting stations and car-park drainage pumps are a regular part of the work, particularly in north Surrey and in buildings with underground parking. They fail in the same ways as a development station, and they need a tested alarm that actually reaches someone.

What do you need in order to quote for a new packaged station?

The site location, whether the duty is foul or surface water, a sense of the incoming flow or the number of properties served, the approximate invert level and the discharge point, and any preference for adoption (Section 104) or a private station. If you have drawings or a specification, send them. If you do not, we can help work out the duty from a site visit.

Are your engineers trained for confined-space work?

Yes. Service engineers are trained for confined-space working and take regular refreshers in gas detection, breathing apparatus, confined-space entry procedures and the associated health and safety requirements. That is a basic requirement for working in wet wells, not an optional extra.

Do you work for managing agents and housing associations as well as developers?

Yes. A large part of planned servicing is for people who did not choose the original station — managing agents, facilities managers and housing associations who have taken on an adopted-pending or unadopted asset, or an older chamber on a managed block. We also install new stations for developers and groundworkers.